ElectriFly Pluma 3D EP ARF Biplane
This is the electric powered, radio controlled, almost ready to fly
ElectriFly by Great Planes Pluma 3D Biplane.
Park Pilot Program Legal Aircraft
For Intermediate Modeler/Pilots.
Can be flown indoors or outdoors.
Construction: Lightweight 0.12" (3mm) extruded polystyrene Pro-
Formance foam-an ElectriFly exclusive, tabbed and interlocking for
fast assembly and correct alignment, pre-applied graphics are
lighter weight than paint
all flying surfaces (except rudder) pre-hinged with genuine 3M
Blenderm tape which is durable and feather light
Wings: Both sections with ailerons, speed brakes install between
aileron link rods if desired
Aileron Control: Single servo
Landing Gear: Carbon rod with factory bent wire ends
Hardware: Carbon fiber and laser cut
Building Time: Ready to fly in about one hour
Warranty: Great Planes Model Manufacturing Company guarantees this
kit to be free from defects in both materials and workmanship at
the date of purchase.
ElectriFly by Great Planes Pluma 3D Biplane, instruction manual,
decal sheet, landing gear with two 1" (26mm) diameter plastic
Radio: 4 channel with micro receiver
Servos: Three micro high torque (1-rudder, 1-elevator, 1-aileron)
Battery Charger: LiPo compatible
For Indoor Flight-
Motor: Rimfire Outrunner Brushless 28-22-1380, GPMG4505
ESC: Silver Series For Brushless Motors 8A, GPMM1800
Battery: Power Series 11.1V 300mAh Balanced 18C LiPo Pack
Propeller: 8x4 thin prop, GWSQ2009
For Outdoor Flight-
Motor: Rimfire Outrunner Brushless 28-26-1000, GPMG4525
ESC: Silver Series For Brushless Motors 12A, GPMM1810
Battery: BP Series 11.1V 640mAh Balanced 15C LiPo Pack
Propeller: 10x4.7 Slow Flyer, APCQ5015
Wingspan: 32.5" (830mm)
Wing Area: 518 sq in (33.4 sq dm)
Weight: 8.4 - 9.5oz (240 - 270g)
Wing Loading: 2.3 -2.6oz/sq ft (7.2 - 8.1g/sq dm)
Length: 38" (955mm)
Center of Gravity:
Indoor Flying, 2-5/8" (67mm) from the leading edge of upper wing
Outdoor Flying, 2-1/2" (63mm) from the leading edge of upper wing
Total C.G. range is from 1-3/4" (44mm) forward to 3-5/16"
(85mm) aft. Do not fly outside of this range
Low Rate High Rate 3D Rate
Elevator: 1" (25mm) 17° 1-3/8" (35mm) 26° 2-1/8" (55mm) 46°
Rudder: 1-9/16" (40mm) 19° 2-3/4" (70mm) 36° 3-7/8" (100mm) 56°
Ailerons: 1-9/16" (40mm) 27° 2-3/8" (60mm) 43° 2-7/8" (75mm) 58°
- Assembles in about an hour - and excels indoors and out!
- Largely prebuilt, with keyed and laser-cut parts that speed the completion of remaining steps.
- Performs everything from traditional air show aerobatics to all-out 3D stunts!
- Lightweight 0.12" (3mm) extruded polystyrene Pro-Formance foam - an ElectriFly exclusive, tabbed and interlocking for fast assembly and correct alignment, pre-applied graphics are lighter weight than paint. All flying surfaces (except rudder) pre-hinged with genuine 3M Blenderm tape which is durable and feather light.